亚洲综合无码久久精品综合 I 人妻互换一二三区激情视频 I 国产福利视频一区二区 I 夜夜高潮夜夜爽夜夜爱爱 I 欧美又大粗又爽又黄大片视频 I 激情爆乳一区二区三区 I xx性欧美肥妇精品久久久久久 I 日韩精品专区在线影院重磅 I 亚洲精品久久久久久一区二区 I av香港经典三级级 在线 I 少妇熟女视频一区二区三区 I 日本亚洲色大成网站www久久 I 狠狠躁夜夜躁人人爽天天5 I 亚洲最大的成人网 I 正在播放酒店约少妇高潮 I 在线成人精品国产区免费 I av片在线播放 I 国产精品久久久久久超碰 I b站永久免费看片大全 I 久久婷婷国产剧情内射白浆 I 亚洲爆乳精品无码一区二区三区 I 国产一卡二卡三卡四卡 I 玩弄中年熟妇正在播放 I 国产精品久久久久久亚洲色 I 级r片内射在线视频播放 I 欧美牲交a欧美牲交aⅴ I 一区二区视频 I 免费看成人欧美片爱潮app I 水蜜桃色314在线观看 I 亚洲在线 I 久久久精品一区aaa片 I 熟妇人妻无乱码中文字幕真矢织江 I 国产亚洲精品久久久久久打不开 I 国产精品无码久久久久久 I 无码人妻精品一区二区在线视频

Due to the special structure of plastic surface, although the surface of plastic parts is modified through surface pretreatment, the weak interface layer is removed, the surface of plastic parts is activated, and the adhesion of coating film is increased, the selection of coating, coating process and coating environment management in the manufacturing of mechanical plastic shell will also affect the coating quality.

Therefore, the selection of mechanical plastic shell coating should follow the "similar phase solubility principle", in order to ensure the good miscibility of ABS and coating resin and solvent, make the coating film and plastic surface form a very thin mutually soluble layer, enhance the adhesion, not only have a good decorative effect, but also meet the physical and chemical performance requirements of the paint film.

At present, mechanical plastic shell coating mostly use manual air spraying process, labor intensity, poor working environment, coating efficiency is only about 20% ~ 30%, paint loss, high cost, man-made quality instability factors directly affect the quality of products.

With the development of science and technology, mechanical plastic shell manufacturing industry in the mold coating in the plastic processing development is very fast, that is, the use of electrostatic coating coating in the mold wall, in the plastic molding, at the same time to complete the surface coating of plastic parts. Due to the plastic molding temperature is higher, is conducive to the coating curing, the mold itself roughness is very low, therefore, the coating surface is very clean, high gloss.

After the mechanical plastic shell is moulded, the mold is slightly lifted, injected into IMC at high pressure, the mold is closed at high pressure to make IMC fully expanded, and after hardening, the plastic surface is very smooth, it can get high quality decorative products at a low cost, and the moulded parts can be immediately packaged or sent for assembly, very convenient.

The mechanical plastic shell of these two coating technology coatings are solvent-free, no organic solvents in the process of operation, so there is no environmental pollution, paint utilization rate is very high, to avoid heavy painting, no special coating equipment, when the injection is completed painting.